Online

Tuesday, January 29, 2013

Galaxy S Advance I9070 with Jellybean 4.1.1 Firmware

Galaxy S Advance logo 
Procedure to Update Galaxy S Advance I9070 with Jellybean 4.1 Styled Firmware:
  • Once placed, disconnect the device and download the ROM Manager app from the Google PLAY Store so that you can then enter the device in the recovery mode. Alternatively, you can also enter your phone in the recovery mode with the help of below mentioned manual step.
  • Recovery mode in Galaxy S Advance I9070 can be entered manually by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode.
Note: If the device gets stuck in the Samsung logo or gets into the boot loop mode then you need to long press the power button and turn off the device. Repeat the process from the start by following the instructions.

So there you go, you have now successfully updated your Galaxy S Advance I9070 device with the latest version of Jellybean 4.1.1 Styled firmware. Do let us know just in case if you face any issues while you perform the update in the comments section below as we will try our level best to sort out the same.

Monday, January 28, 2013

Root Galaxy S2 I9100 on XWLS8 Jellybean 4.1.2 Firmware

Galaxy S2 Logo Special 
Procedure to Root Galaxy S II GT I9100 on Jellybean XWLS8 4.1.2 Firmware:
  • Turn Off your Galaxy S2 I9100 so that your device can be entered in the Download Mode. Download mode in Galaxy S2 GT I9100 can be entered in recovery mode by pressing the Volume Up rocker key + power button at the same time while the device is turned Off. If the device starts in the normal mode, you need to re try the process of the entering the device into the download mode.
  • Once the device is entered in the Download Mode, Open Odin in your computer and connect your device to the computer with the help of original USB cable and then you will see that the ID: COM section will turn Yellow indicating that all the drivers have been installed successfully.
  • Now, click on “PDA” and then you will have to select “”. Once selected, click on “Start” to start the process of Rooting.
  • Once the device is rooted, the device will be rooted. It will take around 1 -3 minutes for rooting the device. Once the device is rooted, phone will be rebooted.
Note: Just in a rare case if the device is not updated and it gets into the boot loop mode, you need to again clear the cache from the recovery mode and retry the whole process from the start.
  • Download the Root Checker app from the Google PLAY Store to check whether your device is rooted or not.  Also, if it’s rooted, you then will have to download and install the ROM Manager app from the Google PLAY Store.
So, there you go, you have successfully rooted your device on the XWLS8 Firmware which is on the Jellybean 4.1.2 firmware. Do let us know in the comments section just in case if you face any issues in the comments section.

Download and install Update Galaxy Note N8000 with Official Jellybean 4.1.2 XXCLL6 Firmware

Galaxy Note N8000 OTA 
 Procedure to Update XXCLL6 Jellybean 4.1.2 Firmware in Galaxy Note N8000:
  • Open Odin in your computer and turn Off your Galaxy Note N8000 10.1 device so that it can be entered in the download mode.
  • Hold Volume Down rocker key and holding this press the Power button till you see the Warning Screen. Now, on WARNING Screen you will have to press the Volume Up key to enter the device in the download mode.
  • Once your device gets in the download mode, connect your tablet to the computer with the help of original USB cable and then you shall see that in Odin the ID : COM section will turn Yellow indicating that all the drivers have been successfully installed.
  • Now, click on “PDA” tab in Odin and select the tar file which you got after extracting the firmware zip file. Once selected, you need to click on “Start” for starting the process of firmware update.
  • The whole process of firmware update may take about 3 -5 minutes. Once the firmware is update, your tablet will be rebooted automatically and once you see the home screen in your tablet, you can then disconnect the device from computer.
  • Now, to check whether the firmware is updated or not, head over to the path “Settings > About Tablet” where you will get to see the firmware version as jellybean 4.1.2 XXCLL6.
Users Facing Force Close Issues:
Turn Of your Galaxy Note N8000 to enter your device in the recovery mode. In the recovery mode select Wipe data/factory reset and also you need to select Wipe Cache partition and then reboot your device by selecting reboot system now option.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
So, there you go, you have now successfully learnt on how to apply the latest Jellybean 4.1.2 firmware dubbed as XXCLL6 in your Galaxy Note N8000 10.1 Tablet. Do keep us posted in the comments section just in case if you face any issues as we will try to address the same as soon as possible.

Download and install Update Galaxy Grand I9082 with Official Jellybean 4.1.2 XXAMAB Firmware

Galaxy-Grand-Banner 

Procedure to Update Galaxy Grand I9082 with XXAMAB Jellybean 4.1.2 Firmware:
  • Now, open Odin in your computer and turn off your phone so that it can be entered in the Download Mode.
  • Download mode in Galaxy Grand I9082 can be entered by pressing Volume down Key, Center button, and holding both simultaneously press the Power Button after which a green robot will be shown indicating the Download Mode has been entered.
  • Open Odin in your computer. Connect your device to the computer with the help of original USB cable and then you will see that the ID : COM Section will turn Yellow. Just in case if the odin refuses to turn Yellow, you will then have to install the required drivers by removing unknown drivers in USB section and reboot the system once. Preferably you can install the Samsung KIES to get rid of this issue from Samsung.com/KIES.
  • Now, open Odin in your computer and then click on “PDA” to select “” and then click on “start” to start the process of firmware update. As soon as the firmware is updated, the device will be rebooting and then once you see the home screen, you can remove the connected USB and follow the on screen instructions.
  • To check on whether the firmware has been successfully updated or not, head over to the path “Settings > About Phone” where the current firmware will be mentioned as Jellybean 4.1.2 XXAMAB. Very soon we will be coming out with an article which will help you root your Samsung Galaxy Grand device.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
So, there you go, you have now successfully learnt on how to apply the latest Jellybean 4.1.2 firmware dubbed as XXAMAB in your Galaxy Grand I9082 smartphone. Do keep us posted in the comments section just in case if you face any issues as we will try to address the same as soon as possible.

Download and install Update Galaxy Y GT-S5363 with Official Value Pack Gingerbread 2.3.6 Firmware

Samsung Galaxy Y Logo 

Procedure to Update Galaxy Y GT-S5363 with Value pack Gingerbread 2.3.6 Firmware:
  • Turn Off your Galaxy Y GT-S5363 so that it can be entered in the Download Mode. Download Mode in Galaxy Y GT-S5363 can be entered by pressing Volume Down + Menu Button + Power button till you see the Download Mode screen. Just in case if the device boots up in the normal mode, you will have to re try the process of entering the device in the Download Mode.
  • Now, in Odin you need to click on “PDA” to select “S5363XXLL1_S5363NEELL1_S5363XXLL1_HOME.tar.md5” file from the extracted firmware zip file and once it’s done, click on “Start” the process of firmware update. As soon as the firmware is updated successfully, the Galaxy Y GT-S5363 will be rebooted.
  • Once you see the Welcome screen in your Galaxy Y GT-S5363, you will now need to disconnect the device from the computer and use it the way you want to. To check whether the firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where the firmware version will be mentioned as XXLL1 Gingerbread Value Pack Firmware.
Tip: Just in a rare case if the device doesn’t boot up or gets into the continuous Boot loop mode, you need to reinsert the battery and boot the device normally. Or else you need to re-apply the update by following the steps above.

Download and install Update Galaxy S GT I9000 with Stable Jellybean 4.2.1 C-RoM Mix v5.0 Firmware

Procedure to Update Samsung Galaxy S GT I9000 with C-RoM Mix v5.0 Jellybean 4.2.1 firmware:
  • Download the C-RoM Mix 4.2.1 firmware package from here to your computer. Once downloaded, connect your Galaxy S GT I9000 to the computer with the help of original USB cable and place the zip file into the sd card. Ensure that you are not placing the files deep into the sub folders.
  • Recovery mode in Galaxy S GT I9000 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode via the ROM Manager app.
  • Now, in the recovery mode, select “install zip from sd card” > “choose zip from internal sd card” and then choose the C-RoM Mix v5.0 firmware  Package. It will take around 4 -5 minutes for applying the update.
  • Once you see the “install from sd card complete” message on screen, select “Go Back” and select “reboot system now” for rebooting the device in the normal mode.
  • To check on whether the C-RoM Mix v5.0 firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully learnt to update your Galaxy S with C-RoM Mix v5.0 firmware, in the coming days to come we will come with new custom Jellybean 4.2 firmwares for Galaxy S devices.
forum.xda

Wednesday, January 23, 2013

Download and install Update Galaxy S2 GT I9100 with Android 4.1.2 Jelly Bean Firmware

 
[OFFICIAL]Samsung rolls out Android 4.1.2 Jelly Bean update for the Galaxy S II GT-I9100

Samsung has just started to push Android 4.1.2 Jelly Bean update to the International Samsung Galaxy S II GT-I9100. The Galaxy S II is the best-selling Android device of 2011 and has a very large user base that’s why Samsung keeps on updating this device with all the new Android versions as they want to provide the Galaxy S II users with their best support experience.

You might not be able to update your device to Android 4.1.2 Jelly Bean right away as the update is rolling out in phases. So, it might not yet be available for your country or network provider (If Your device is Carrier branded) but don’t worry the update will arrive soon.

In the history of software updates, the new Jelly Bean update by Samsung to the Galaxy S II is by far the most major update given to a smartphone yet. As we all know Samsung’s ICS update didn’t had any UI changes and had exactly the same UI which was in its Gingerbread but this is not the case with Samsung’s Android 4.1.2 Jelly Bean update. The new jelly bean update breathes a new life into the Galaxy S II, Samsung has completely ditched the old UI and has given the new Nature UX Interface, which is the same as the one being used in the Galaxy S III Mini and the Galaxy S III, in its latest Jelly Bean update.

Some of the Enhancements in the new Jelly Bean Update:
- Buttery Smooth Performance & Great Stability (Thanks to Project Butter)
- Full User Interface Revamp (Same UI as of the Galaxy S III and Galaxy Note II)
- TouchWiz Nature UX
- Samsung’s S Cloud services
- Improved Camera features
- New Lockscreen With Many Customization Options
- New Features like Direct Call, Smart Stay and Pop-up Play
- New Widgets (From Galaxy S III)
- 2 Home screen modes
- New Notification bar With More Notification Toggles
- Google Now

Keep an eye on @SamKiesUpdates to get the latest information on Official Firmware updates for your Samsung device.
You can update your Galaxy S II through Samsung KIES or by using OTA.

Hot links:
Check the 10 latest official firmwares for the Galaxy S II here!
You can find our live firmware feed here!

Official Firmware Details:
Android Version: 4.1.2 – Build JZO54K
PDA: I9100XWLS8
CSC: I9100FOPLS3
MODEM: I9100XXLS8
Changelist: 816988
Build Date: 14 January 2013

Live Feed of Official Android 4.1.2 Jelly Bean update availability for the Galaxy S II GT-I9100
XXLS / XWLS / ZSLS / DDLS / JVLS / JPLS
Download

Black iphone Theme for Samsung Corby 2 (smt)

CORBY 2 THEMES: Black iPhone Theme by Anonymous 
 Black iphone Theme for Samsung Corby 2 (smt)
 
This installation guide is for SAMSUNG Corby 2 user...
1.Click the Download button to get the .smt file   
2. Send .smt  file from your PC to your mobile via USB or Bluetooth   
3. Go to MENU > My Files > Themes > Tap the name of the theme (e.g.heroesofnewerth.smt) 
4. Tap Set and Exit and you're done.

Download and install Google Play Store APK v3.10.10

Google Play Store v3.7.15 
Grab the APK file of Google Play Store App v3.10.10 from here – Download Now.

Tuesday, January 22, 2013

Download and install Update Galaxy S2 GT I9100G with Jellybean 4.1.2 Firmware

avatar-rom 
Procedure to Update Galaxy S2 GT I9100G with Avatar ROM Jellybean 4.1.2 firmware:
  • Now, disconnect the device from computer and turn Off the device so that it can be entered in the recovery mode. The recovery mode can be entered either with the help of “ROM Manager” app or manually with the help of below mentioned step.
  • Recovery mode in your Galaxy Device can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. Now, select “install zip from SD Card” in the recovery mode to choose the zip file which you have placed in your device.
  • Now, once the firmware is updated, select “go back” and select “reboot system now”. To check on whether the firmware is updated or not, head over to the path “Settings > About Phone” for checking the same.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.

Download and install Update Galaxy S3 Mini I8190 with Official Jellybean 4.1.2 XXAMA2 Firmware

GALAXY-S3-Mini-iMAGE 
Procedure to Update Samsung Galaxy S3 Mini I8190 with Jellybean 4.1.2 XXAMA2:
  • Download the XXXAMA2 Jellybean 4.1.2 Firmware Package + Odin Package from here to your computer. Once downloaded, extract both of them and open Odin in your computer. You can download the appropriate Firmware Package mentioned below,
  • Turn Off your Galaxy S3 Mini I8190 so that it can be entered in the Download Mode. The download mode in Galaxy S3 Mini I8190 can be entered by pressing  Volume Down Key + OK button, and holding both simultaneously press the Power Button. Now, a Warning message will be shown when you need to press the Volume Up key to continue entering the Download Mode.
  • Now, all you need to do is to just connect your device to the computer with the help of original USB cable and then open the ID : COM section will turn Yellow indicating that all the drivers have been successfully installed.
  • Click on “PDA” to select the TAR File which is having “code” in the file name and the same you will get once you extract the Firmware Zip file which you have downloaded in the initial step.
  • Once the firmware update process is completed successfully, the phone will be rebooted automatically.
  • Disconnect the device from the computer and check from the path “Settings > About Phone” where the current firmware version will be mentioned as Jellybean 4.1.2 firmware XXAMA2. Very soon we will be coming up with an article which will help you to upgrade with the latest Jellybean 4.2.1 firmware version for Galaxy S3 Mini I8190.
Note: Just in a rare case if your Samsung device refuses to turn ON or say if it gets stuck on the Samsung Logo then you need to long press the power button to turn off the same or re insert the battery to start the process from beginning.
Do let us know in the comments section just in case if you face any issues in the process of firmware update as we will try our level best to sort out the same at the earliest.

Download and install Update Galaxy S GT I9000 with Stable Jellybean 4.2.1 Firmware

Jellybean 4.1 Logo 
Procedure to Update Samsung Galaxy S GT I9000 with C-RoM Mix v5.0 Jellybean 4.2.1 firmware:
  • Download the C-RoM Mix 4.2.1 firmware package from here to your computer. Once downloaded, connect your Galaxy S GT I9000 to the computer with the help of original USB cable and place the zip file into the sd card. Ensure that you are not placing the files deep into the sub folders.
  • Recovery mode in Galaxy S GT I9000 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode via the ROM Manager app.
  • Now, in the recovery mode, select “install zip from sd card” > “choose zip from internal sd card” and then choose the C-RoM Mix v5.0 firmware  Package. It will take around 4 -5 minutes for applying the update.
  • Once you see the “install from sd card complete” message on screen, select “Go Back” and select “reboot system now” for rebooting the device in the normal mode.
  • To check on whether the C-RoM Mix v5.0 firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully learnt to update your Galaxy S with C-RoM Mix v5.0 firmware, in the coming days to come we will come with new custom Jellybean 4.2 firmwares for Galaxy S devices.

Download and install Update Galaxy S2 GT I9100 with Jellybean 4.1.2 Firmware

s2 

Procedure to Update Galaxy S2 GTI9100 with Jellybean 4.1.2 Firmware:
  • Download the latest Jellybean 4.1.2 Firmware Package from here to your computer. Once downloaded, connect your device to the computer and place the zip file in the internal memory of your S2.
  • Disconnect the device so that your phone can be entered in the recovery mode. The recovery mode in Galaxy S2 can be entered either by ROM Manager or with the help of below mentioned manual method which we have mentioned below.
  • Recovery mode in Galaxy S2 GT I9100 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. Now, select “install zip from SD Card” in the recovery mode to choose the zip file which you have placed in your device.
  • It will take around 3 -5 minutes for applying the update and as soon as it’s updated successfully, you will need to then make sure to follow all the on screen instructions. Once you see the message as “install from sd card completed”, select “go back” and select “reboot system now” for rebooting the device in the normal mode.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Once updated, you can now restore all the data which you have created a backup of all the data. Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same.

Download and install Update Galaxy S3 I9305 with Official Jellybean 4.1.2 XXBMA3 Firmware

Galaxy S3 Hyderabad Logo 
Procedure to Update Galaxy S3 I9305 with XXBMA3 Jellybean 4.1.2 Firmware Update:
  • Turn Off your phone so that it can be entered in the download mode. Download mode in Galaxy S3 GT I9300 can be entered by pressing Volume down Key, Center button, and holding both simultaneously press the Power Button after which you will get to see a green robot indicating that the device has entered in the download mode.
  • Connect your phone in the download mode to the computer while keeping Odin opened. Once you connect, you will see that the ID: COM section will turn Yellow indicating that all the drivers have been successfully installed.
  • Click on “PDA” to select “TAR File” which you got after extracting the firmware file and then click on “Start” to start the process of firmware update. As soon as the firmware is updated successfully, the device will be rebooted automatically indicating that the firmware has been updated successfully.
  • Once you see the home screen, disconnect the device and head over to the path “Settings > About Phone” where you will be able to see the firmware version as Jellybean 4.1.2 firmware XXBMA3.
Tip: Just in a rare case if the device doesn’t boot up or gets into the continuous Boot loop mode, you need to reinsert the battery and boot the device normally. Or else you need to re-apply the update by following the steps above.

Download and Root Galaxy S3 GT I9305 on XXBMA3 Jellybean 4.1.2 Firmware

Samsung 
Procedure to Root Galaxy S3 GT I9305 on XXBMA3 Jellybean 4.1.2 Firmware:
  • Download XXBMA3 Jellybean 4.1.2 Firmware Package from here to your computer which contains Odin as well. Once downloaded, extract both of the files in your computer and open Odin in your computer.
  • Turn Off your device so that it can be entered in the Download Mode. Download mode in Galaxy S3 GT I9300 can be entered by pressing Volume down Key, Center button, and holding both simultaneously press the Power Button after which you will get to see a green robot indicating that the device has entered in the download mode.
  • Connect your phone in the download mode to the computer while keeping Odin opened. Once you connect, you will see that the ID: COM section will turn Yellow indicating that all the drivers have been successfully installed. Also, in Odin ensure that Auto Reboot and F. Reset Time checkboxes are selected and no other options are
  • Now, click on “PDA” to select “CF-Auto-Root-m3-m3zh-gti9305.tar.md5” and then click on “Start” to start the process of Rooting. Once the device is rooted, download the “ROOT CHECKER” app from the Google PLAY Store to check on whether the device is rooted or not. Just in case if the device is not rooted, you need to retry the process of rooting.
Tip: Just in a rare case if the device doesn’t boot up or gets into the continuous Boot loop mode, you need to reinsert the battery and boot the device normally. Or else you need to re-apply the update by following the steps above.
So there you go, you have now successfully rooted your Jellybean 4.1.2 XXBMA3 Firmware loaded Samsung Galaxy S3 I9305 smartphone. Do let us know in the comments section just in case if you face any issues so that we can assist you as soon as possible.

Download and install Update Galaxy ACE S5830 with S3 Looking TouchWiz 5.0 Firmware

Galaxy ACE Logo 
Screen Captures 7.2 
Procedure to Update Samsung Galaxy ACE S5830 with the latest Cyanogen MOD 7.2 Styled SGS 3 TW5 Firmware:
  • Download the CM 7.2 – SIII MOD v2 Package from here to your computer. Once downloaded, connect your device to the computer with the help of original USB cable and place the downloaded zip file in your device. Once copied, disconnect the device from the computer.
  • Download the “ROM Manager” app from the Google PLAY Store and install the same. Once installed, open the same and select the option of “Reboot in Recovery Mode” for entering the device in the recovery mode. For manually entering the device in recovery mode, press and hold the Menu Button and then Power ON the device. If the device turns ON in the normal mode then you need to try again to enter into the recovery mode.
  • In the recovery mode, you need to select “install zip from sd card” > “choose zip from sd card” and then choose the CM 7.2 – SIII MOD v2 Package file which is placed in the phone. Once selected, it will take round about 5 -6 minutes for applying this update.
Tip: If your Galaxy ACE doesn’t power up or say it gets into the boot loop mode, you need to re insert the battery and then re try the process of firmware update by following the above steps.
Do share with us in the comments section just in case if you face any issues in the comments section as we will try our level best to sort out the same. Congrats, you have now successfully applied the update of CM 7.2 – SIII MOD v2 in your Galaxy ACE S5830.

 

Download and install Update Galaxy Camera with Improvised Jellybean 4.1.2 KSALL4 Firmware

Galaxy Camera Home Screen 
Procedure to Update Galaxy Camera with Jellybean 4.1.2 Firmware:
  • Turn Off your Galaxy Camera so that it can be entered in the Download Mode. Download Mode in Galaxy Camera can be entered by pressing Volume Down + Camera + Power button till you see the Download Mode screen. Just in case if the device boots up in the normal mode, you will have to re try the process of entering the device in the Download Mode.
  • Now, in Odin you need to click on “PDA” to select “I8190XXAMA2_I8190QBLAMA1_HOME.tar.md5” file from the extracted firmware zip file and once it’s done, click on “Start” the process of firmware update. As soon as the firmware is updated successfully, the Galaxy Camera will be rebooted.
  • Once you see the Welcome screen in your Galaxy Camera, you will now need to disconnect the device from the computer and use it the way you want to. To check whether the firmware has been updated or not, you need to check the same from the path “Settings > About Camera” where the firmware version will be mentioned as KSALL4 Jellybean 4.1.2 version.
Tip: Just in a rare case if the device doesn’t boot up or gets into the continuous Boot loop mode, you need to reinsert the battery and boot the device normally. Or else you need to re-apply the update by following the steps above.

Download and install Update Galaxy Y GT-S5363 with Official Value Pack Gingerbread 2.3.6 Firmware

Samsung Galaxy Y Logo 
Procedure to Update Galaxy Y GT-S5363 with Value pack Gingerbread 2.3.6 Firmware:
  • Turn Off your Galaxy Y GT-S5363 so that it can be entered in the Download Mode. Download Mode in Galaxy Y GT-S5363 can be entered by pressing Volume Down + Menu Button + Power button till you see the Download Mode screen. Just in case if the device boots up in the normal mode, you will have to re try the process of entering the device in the Download Mode.
  • Now, in Odin you need to click on “PDA” to select “S5363XXLL1_S5363NEELL1_S5363XXLL1_HOME.tar.md5” file from the extracted firmware zip file and once it’s done, click on “Start” the process of firmware update. As soon as the firmware is updated successfully, the Galaxy Y GT-S5363 will be rebooted.
  • Once you see the Welcome screen in your Galaxy Y GT-S5363, you will now need to disconnect the device from the computer and use it the way you want to. To check whether the firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where the firmware version will be mentioned as XXLL1 Gingerbread Value Pack Firmware.
Tip: Just in a rare case if the device doesn’t boot up or gets into the continuous Boot loop mode, you need to reinsert the battery and boot the device normally. Or else you need to re-apply the update by following the steps above.
Do let us know in the comments section just in case if you face any issues so that we can assist you as soon as possible. Very soon we will be also coming out with ICS firmware update for Galaxy Y GT-S5363.

Download and install Update Galaxy S2 GT I9100 with Jellybean 4.2.1 Firmware Update – Super Stable Resurrection Remix

Video thumbnail for youtube video How to Update Galaxy S2 with S3 Looking Salman ICS 4.0.3 Custom ROM Firmware - Android Advices 
Procedure to Update Galaxy S II GT I9100 phone with Resurrection Remix Firmware:
  • After placing the files in your device, download the “ROM Manager” app from the Google PLAY Store. Now, all you need to do is to disconnect the device from computer and enter your Galaxy S2 in the recovery mode. You can either enter the device in the recovery mode with the help of ROM manager app or manually with the help of below mentioned step.
  • Turn Off your phone so that it can be entered in the download mode. Recovery mode in Galaxy S2 GT I9100 can be entered by pressing Volume Up Key, Center button, and holding both simultaneously press the Power Button after which you will get to see a green robot indicating that the device has entered in the recovery mode.
  • In recovery mode, select “install zip from sd card” and choose the Resurrection Remix Custom ROM firmware and then the Add-On Package. Once the firmware is selected, it will take around 4 -5 minutes for applying the update. Once the firmware is updated successfully, you will see the message as “install from sd card completed” and then all you need to do is to just select “go back” and select “reboot system now” for rebooting the device in the normal mode.
  • To check whether the firmware is updated or not, check from the path “Settings > About Phone” where the current firmware version will be mentioned as Jellybean 4.2.1 Resurrection Remix firmware. Very soon we will be coming up with an article which will help you to upgrade with the latest Jellybean 4.2.1 firmware version for Galaxy S II.
Note: Just in a rare case if your Samsung device refuses to turn ON or say if it gets stuck on the Samsung Logo then you need to long press the power button to turn off the same or re insert the battery to start the process from beginning.
Do let us know in the comments section just in case if you face any issues in the process of firmware update as we will try our level best to sort out the same at the earliest. So, there you go, you have successfully updated your device with the latest firmware.

Download and install Update Galaxy S Advance I9070 with Official Jellybean 4.1.2 XXLPY Firmware

Galaxy S Advance logo 
Procedure to Update Galaxy S Advance I9070 with Jellybean 4.1.2 Firmware:
  • Download Jellybean 4.1.2 Firmware Package and Odin from here to your computer. Once downloaded, connect your device to the computer and extract both the zip files downloaded in your computer.
  • Open Odin in your computer and you will see that the ID: COM section will turn Yellow indicating that all the drivers are installed successfully.
  • Now, click on “PDA” to select the tar file which you have got after extraction and click on “Start” to start the process of firmware update. As soon as the firmware is updated successfully, you will see that the device will be rebooted automatically. The whole process of firmware update will take around 4 -5 minutes.
  • Once you see the Welcome screen in your Galaxy S Advance I9070, you will now need to disconnect the device from the computer and use it the way you want to. To check whether the firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where the firmware version will be mentioned as XXLPY Jellybean 4.1.2 version.
Note: If the device gets stuck in the Samsung logo or gets into the boot loop mode then you need to long press the power button and turn off the device. Repeat the process from the start by following the instructions.

So there you go, you have now successfully updated your Galaxy S Advance I9070 device with the latest version of Jellybean 4.1.2 firmware. Do let us know just in case if you face any issues while you perform the update in the comments section below as we will try our level best to sort out the same.

Wednesday, January 9, 2013

Download and install Update Galaxy S GT I9000 with Official Jellybean 4.2.1 Firmware

Procedure to Update Galaxy S GT I9000 with Jellybean 4.2 Firmware:
  • Download the Jellybean 4.2.1 Firmware package from here to your computer. Once downloaded, connect your device to the computer with the help of original USB cable and then place these two zip files in your device.
  • Once you have placed these two files, disconnect the device from computer to download the “ROM Manager” app from PLAY Store. Open the app and grant the Superuser access by tapping on the “Grant” option.
  • Now, from the ROM Manager app, select “Enter into Recovery Mode” for booting the device in the recovery mode or else you can also manually enter the device in the recovery mode by first turning Off the device. Recovery mode in Galaxy S GT I9000 can be entered manually by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode.
  • Now, select “install zip from sd card” to choose the placed jellybean 4.2.1 Zip Package and Google Apps Package. It will take around 3 – 5 minutes for applying the update. Please note that sometimes it may take more than expected time for updating the same.
  • Now, once the firmware is updated, select “go back” and select “reboot system now”. To check on whether the firmware is updated or not, head over to the path “Settings > About Phone” for checking the same.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.

Download and install Update Galaxy S Advance I9070 with Jellybean 4.1.1 Firmware

Galaxy S Advance logo 
Procedure to Update Galaxy S Advance I9070 with Jellybean 4.1 Styled Firmware:
  • Once placed, disconnect the device and download the ROM Manager app from the Google PLAY Store so that you can then enter the device in the recovery mode. Alternatively, you can also enter your phone in the recovery mode with the help of below mentioned manual step.
  • Recovery mode in Galaxy S Advance I9070 can be entered manually by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode.
Note: If the device gets stuck in the Samsung logo or gets into the boot loop mode then you need to long press the power button and turn off the device. Repeat the process from the start by following the instructions.

Download and install Update Galaxy Note N7000 with Official Jellybean 4.1.2 XXLSA Firmware

Jellybean 4.1.2 Logo 
Procedure to Update Galaxy Note N7000 with Jellybean 4.1.2 XXLSA Firmware:
  • Download XXLSA Jellybean 4.1.2 Firmware Package from here to your computer along with Odin in your computer. Once downloaded extract both of them preferably to the folders on Desktop. Once extracted, open odin in your computer and turn off your Galaxy Note so that it can be entered in the Download Mode.
  • The download mode can be entered by pressing Volume Down Key + OK button, and holding both simultaneously press the Power Button. Just in case if the device turns ON in the normal mode, you will have to again retry entering the device in the download mode.
  • Connect your phone to computer with the help of original USB cable and then you will see that the ID : COM section will turn Yellow which will mean that all the drivers have been installed successfully and you are ready to proceed to the next step wherein you will have to click on the below mentioned corresponding tabs to select the file from extracted firmware package.
PDA – CODE_N7000XXLSA_549786_REV02_user_low_ship.tar.md5,
Phone – MODEM_N7000XXLSA_REV_05_CL1222228.tar.md5,
CSC – CSC_OXA_N7000OXALSA_549786_REV02_user_low_ship.tar .md5
  • Make sure that Re-Partition option is unticked and nothing should be added in the PIT section. Once you are done with all the above mentioned selections, you can now head over to the next step wherein you need to click on “Start” to start the process of firmware update.
  • It will take around 3 -4 minutes for applying the firmware, once the firmware is updated successfully you will see that device will be rebooting on its own.
  • To check on whether the firmware is updated or not, head over to the path “Settings > About Phone” for checking the same where you will see the version details as XXLSA Jellybean 4.1.2 firmware.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same.

Download and install Galaxy S GT I9000 with Stable Jellybean 4.2.1 Firmware


Procedure to Update Samsung Galaxy S GT I9000 with C-RoM Mix v5.0 Jellybean 4.2.1 firmware:
  • Download the C-RoM Mix 4.2.1 firmware package from here to your computer. Once downloaded, connect your Galaxy S GT I9000 to the computer with the help of original USB cable and place the zip file into the sd card. Ensure that you are not placing the files deep into the sub folders.
  • Recovery mode in Galaxy S GT I9000 can be entered by holding the Volume Up button + the Home key button (the middle button). While holding these both buttons, turn ON your device.
  • In recovery mode, select “Wipe data/factory reset” & “Wipe Cache partition”. If the device starts normally, then you will need to re try the process of entering the device in the recovery mode. You can also enter the device in recovery mode via the ROM Manager app.
  • Now, in the recovery mode, select “install zip from sd card” > “choose zip from internal sd card” and then choose the C-RoM Mix v5.0 firmware  Package. It will take around 4 -5 minutes for applying the update.
  • Once you see the “install from sd card complete” message on screen, select “Go Back” and select “reboot system now” for rebooting the device in the normal mode.
  • To check on whether the C-RoM Mix v5.0 firmware has been updated or not, you need to check the same from the path “Settings > About Phone” where you will find the firmware version.
Note: Just in a rare case if the device doesn’t boot up or show the home screen then remove the battery and reinsert the same to boot the device again in the normal mode.
Do share with us in the comments section just in case if you face any issues as we will try our level best to sort out the same. Congratulations, you have now successfully learnt to update your Galaxy S with C-RoM Mix v5.0 firmware, in the coming days to come we will come with new custom Jellybean 4.2 firmwares for Galaxy S devices.

Twitter Delicious Facebook Digg Stumbleupon Favorites More

 
Design by Free WordPress Themes | Bloggerized by Lasantha - Premium Blogger Themes | belt buckles
Design Downloaded from Free Blogger Templates | Free Website Templates